Ultrasuperpingu: /* Switches */

2022-03-05T13:35:14Z

Switches

New page

==Introduction==
'''RFPlayer 1000 by Ziblue''', the USB interface which allows to connect all the wireless devices in your house! In the form of a USB key, this little tool works with the protocols usually used with home automation devices: SOMFY RTS (roller shutters, automatic gates), DELTADORE X2D (alarms, heating, home automation), VISONIC (alarms), CHACON/DIO (home automation), SCIENTIFIC OREGON (peripherals for weather stations) and others.

4 main features:

- "Gateway": allows USB connection for all wireless devices in the house using the protocols quoted above.

- "Parrot": stores 433Mhz and 868Mhz radiofrequency frames, and then recognition and transmission.

- "Repeater": amplifies again the signal in order to avoid reach problems, very common with home automation transmissions.

- "Transcoder": converts input frames from a protocol to an output protocol.

Note: In 2021, GCE Electronics took over the manufacture of the "ZiKey" RFPlayer RFP1000 previously manufactured by the ZiBlue company.

==Instructions==
===Setup Hardware===
First Plugin you RFPlayer to your Domoticz machine

*Go to Setup -> Hardware
*Select Type: RFPlayer Gateway USB
*Select correct com port (on rpi ex. /dev/ttyUSB30)
*Give it a name. Ex RFPlayer
*Push Add

Now if you have "Accept new hardware" enabled under menu [[Application Settings|Setup - Settings]], it should start to populate the device list with new devices. Add them by the green arrow.

In French: https://www.planete-domotique.com/blog/2017/05/05/utilisation-rfplayer-domoticz/

===Setup Devices===
====Sensors====
Sensors like OREGON temperature/humidity sensors should be created when the first message is received from it. Just go to the Setup -> Devices page set the device to used ("Add Device" button with a right green arrow icon).
{| class="wikitable"
|+ Supported Protocols
|-
! Protocol !! Device Created
|-
|X10 / Domia Lite protocols || Switch
|-
|X10 (24/32 bits ID), CHACON , KD101, BLYSS, JAMMING || Switch
|-
|VISONIC /Focus/Atlantic/Meian Tech || None yet, only logged
|-
|RFY (RTS remotes) || Switch
|-
|Scientific Oregon (thermo/hygro sensors) || Temp/Hum Sensor or Temp Sensor
|-
|Scientific Oregon (Atmospheric pressure sensors) || Temp/Hum/Baro Sensor
|-
|Scientific Oregon (Wind sensors) || Wind Sensor
|-
|Scientific Oregon (UV sensors) || Solar Radiation Sensor
|-
|OWL (Energy/power sensors) || Watt Meter Sensor, kWh Meter Sensor, optionaly Watt Meter Sensor * 3 if three-phase
|-
|OREGON (Rain sensors) || Rain Rate Sensor, Rain Sensor
|-
|Thermostats X2D || None yet, only logged
|-
|Alarm/remote control devices X2D || None yet, only logged
|-
|Cartelectronic TIC/Pulses devices (Teleinfo/TeleCounters) || Watt Meter Sensor, kWh Meter Sensor * 2
|-
|FS20 || None yet, only logged
|-
|EDISIO || None yet, only logged
|}

====Switches====
To add a switch (for example, to control somfy blinds):
*Configure your devices with RFPlayer Configurator (you can download it at https://myrfplayer.com/)
*Go to Switches tab
*Manual Light/Switch button
*Fill the name field
*Choose the switch type
*Set the Type: this is the protocol of your device
*Set the pseudo X10 address (A1-P16) (the one you used to configure it with RFPlayer Configurator)
*For RTS protocol, set the qualifier (true if not a blind).
*Press "Add Device"

{| class="wikitable"
|+ Supported Protocols
|-
! Protocol !! Parameters !! Device Example
|-
| Visonic 433MHz || House Code ||
|-
| Visonic 868MHz || House Code ||
|-
| Chacon || House Code ||
|-
| Domia || House Code ||
|-
| X2D 433MHz || House Code ||
|-
| X2D 868MHz || House Code ||
|-
| X2D SHUTTER || House Code ||
|-
| X2D ELEC || House Code ||
|-
| X2D GAS || House Code ||
|-
| RTS || House Code, Qualifier || Somfy RTS Stores
|-
| Blyss || House Code ||
|-
| Parrot || House Code || Devices learnt in parrot mode of RFPlayer
|-
| KD101 || House Code ||
|-
| FS20 868 || House Code ||
|-
| EDISIO || House Code ||
|}

ZiBlue RFPlayer - Revision history

Ultrasuperpingu: /* Switches */