https://wiki.domoticz.com/index.php?action=history&feed=atom&title=Popp_KfobPopp Kfob - Revision history2026-09-18T20:45:41ZRevision history for this page on the wikiMediaWiki 1.46.0https://wiki.domoticz.com/index.php?title=Popp_Kfob&diff=14863&oldid=prevWalter vl at 16:20, 30 December 20202020-12-30T16:20:23Z<p></p>
<p><b>New page</b></p><div>==Changing the manufacturer_specific.xml==<br />
The Popp Kfob has already been added to the manufacturer_specific.xml but under the manufacturer Z-Wave.Me<br />
My Kfob is recognized under manufacturer Popp and thus the manufacturer_specific.xml needs to be edited to support my Popp Kfob<br />
<br />
Add the this to Popp:<br /><br />
<Product type="0100" id="0103" name="Popp KFOB-C Remote Control" config="zwave.me/ZME_KFOB-S.xml" /><br />
<br />
For example:<br /><br />
<Manufacturer id="0154" name="Popp"><br /><br />
...<br /><br />
<Product type="0100" id="0103" name="Popp KFOB-C Remote Control" config="zwave.me/ZME_KFOB-S.xml" /><br /><br />
...<br /><br />
</Manufacturer><br />
<br />
Note: I will create a pullrequest for OpenZwave for this. When it is included then this step is not needed anymore.<br />
<br />
==Adding the Popp Kfob to Domoticz==<br />
'''1. Reset the Kfob'''<br />
<br />
'''2. Include (secure) the Software Remote in 'Gateway Mode', the new Node should now show up in the Nodes Table'''<br />
Notice you must use secure inclusion<br />
<br />
[[File:Popp_Kfob_NodesTable.png]]<br />
<br />
In the above case, the new node has ID 039 , that is 0x27 hexadecimal<br />
<br />
'''3. Add the Controller (Node 1, the zwave USB stick) to all groups of the Kfob:'''<br />
<br />
[[File:NodeDropdown.png]]<br />
<br />
[[File:Popp_Kfob_GroupEditor.png]]<br />
<br />
'''4. Select the Soft Remote node from the nodes table, and change the following parameters'''<br />
<br />
1: In pair with double clicks<br /><br />
2: In pair with double clicks<br /><br />
11: Send Scene<br /><br />
12: Send Scene<br /><br />
13: Send Scene<br /><br />
14: Send Scene<br />
<br />
[[File:Popp_Kfob_NodeSettings.png]]<br />
<br />
Press the button labeled 'Apply Configuration' at the bottom of the above settings:<br />
<br />
[[File:NodeSettingsApply.png]]<br /><br />
press a button on the remote to wake it, and wait about 10 seconds.<br />
<br />
'''5. When you now switch to the 'Log' view, and press a button, you will see we have a connection:'''<br />
<br />
You can press normal, long press, double press etc..<br />
<br />
I suggest to press a button, then switch to the devices view, and you will see the last received button on top (if you order by date/time)<br />
<br />
<br />
'''6. Remember to wake up the popp'''<br />
<br />
by go to maintenance mode by pressing all for buttons (flashing green light) and the press button 2 (upper right) this will allow the popp to fetch the new settings.<br />
[[Category:Z-Wave]]</div>Walter vl