Intergas Incomfort Heater control - Revision history

Walter vl: /* Configure Domoticz */

2025-06-20T09:39:56Z

Configure Domoticz

← Older revision		Revision as of 09:39, 20 June 2025
Line 15:		Line 15:
	* Data Timeout: "Disabled".		* Data Timeout: "Disabled".

	* IP address: IP address of the LAN2RF Gateway ~~under Remote address~~.		* Remote address: IP address of the LAN2RF Gateway.

	* ~~port~~: default 80		* Port: default: 80

	* username: admin		* username: admin

Walter vl at 09:38, 20 June 2025

2025-06-20T09:38:00Z

← Older revision		Revision as of 09:38, 20 June 2025
Line 9:		Line 9:
	Navigate to '''Settings -> Hardware'''		Navigate to '''Settings -> Hardware'''

	Choose "Intergas InComfort LAN2RF Gateway as Type" and fill in the appropriate fields:		Choose "Intergas InComfort LAN2RF Gateway" as Type and fill in the appropriate fields:

	* Name For example, type "Intergas InComfort"		* Name For example, type "Intergas InComfort"

Walter vl at 22:18, 19 June 2025

2025-06-19T22:18:41Z

@@ Line 7: / Line 7: @@
 === Configure Domoticz ===
-Navigate to Settings -> Hardware
+Navigate to '''Settings -> Hardware'''
-Choose "Intergas InComfort LAN2RF Gateway as Type" and fill in the appropiate fields:
+Choose "Intergas InComfort LAN2RF Gateway as Type" and fill in the appropriate fields:
 * Name For example, type "Intergas InComfort"
@@ Line 27: / Line 27: @@
 Once Domoticz has successfully established contact with the gateway, it will automatically create all devices.
-Under Settings -> Devices, there are now 10 new devices. Click on the green arrows to add the devices to your overview.
+Under menu '''Settings -> Devices''', there are now 10 new devices. Click on the green arrows to add the devices to your overview.
 You can then adjust the names to what makes sense to you (as has already been done below)
@@ Line 38: / Line 38: @@
 The setpoint device is sometimes set to 0 by the real thermostat or the app, which makes it unusable in domoticz.
-So set it to NOT ACTIVE (see the green arrow behind the device)
+* So set Thermostat override to NOT ACTIVE (see the green arrow behind the device)

Walter vl at 22:02, 19 June 2025

2025-06-19T22:02:18Z

← Older revision		Revision as of 22:02, 19 June 2025
Line 3:		Line 3:
	From version 2022.2 the thermostat setting also works with the V2 gateway.		From version 2022.2 the thermostat setting also works with the V2 gateway.

			=== Prerequisites ===
	Make sure the Gateway, app and thermostat work as they should, then you can get started with Domoticz.		Make sure the Gateway, app and thermostat work as they should, then you can get started with Domoticz.

			=== Configure Domoticz ===
	Navigate to Settings -> Hardware		Navigate to Settings -> Hardware

	Choose Intergas InComfort LAN2RF Gateway at the ~~bottom under Type~~		Choose "Intergas InComfort LAN2RF Gateway as Type" and fill in the appropiate fields:

	For example, type "Intergas InComfort" ~~under name~~		* Name For example, type "Intergas InComfort"

	~~Set data~~ Timeout to "~~not active~~".		* Data Timeout: "Disabled".

	~~Enter the~~ IP address of the LAN2RF Gateway under Remote address.		* IP address: IP address of the LAN2RF Gateway under Remote address.

	~~Then enter~~ port, username ~~and~~ password		* port: default 80

			* username: admin

			* password: The password that is shown on the back of your gateway. (which you can change via the web interface if you point your browser at the IP address of the gateway)

	[[File:Intergas Incomfort gateway-.png]]		[[File:Intergas Incomfort gateway-.png]]

Walter vl: Created page with "To connect the Intergas Incomfort LAN2RF Gateway, Domoticz includes standard support for the Incomfort. From version 2022.2 the thermostat setting also works with the V2 gateway. Make sure the Gateway, app and thermostat work as they should, then you can get started with Domoticz. Navigate to Settings -> Hardware Choose Intergas InComfort LAN2RF Gateway at the bottom under Type For example, type "Intergas InComfort" under name Set data Timeout to "not active". E..."

2025-06-19T21:55:20Z

Created page with "To connect the Intergas Incomfort LAN2RF Gateway, Domoticz includes standard support for the Incomfort. From version 2022.2 the thermostat setting also works with the V2 gateway. Make sure the Gateway, app and thermostat work as they should, then you can get started with Domoticz. Navigate to Settings -> Hardware Choose Intergas InComfort LAN2RF Gateway at the bottom under Type For example, type "Intergas InComfort" under name Set data Timeout to "not active". E..."

New page

To connect the Intergas Incomfort LAN2RF Gateway, Domoticz includes standard support for the Incomfort.

From version 2022.2 the thermostat setting also works with the V2 gateway.

Make sure the Gateway, app and thermostat work as they should, then you can get started with Domoticz.

Navigate to Settings -> Hardware

Choose Intergas InComfort LAN2RF Gateway at the bottom under Type

For example, type "Intergas InComfort" under name

Set data Timeout to "not active".

Enter the IP address of the LAN2RF Gateway under Remote address.

Then enter port, username and password

[[File:Intergas Incomfort gateway-.png]]

Once Domoticz has successfully established contact with the gateway, it will automatically create all devices.

Under Settings -> Devices, there are now 10 new devices. Click on the green arrows to add the devices to your overview.

You can then adjust the names to what makes sense to you (as has already been done below)

After this, you can simply operate the thermostat (the setpoint device)

[[File:Intergas Incomfort devices-.png]]

The setpoint device is sometimes set to 0 by the real thermostat or the app, which makes it unusable in domoticz.

So set it to NOT ACTIVE (see the green arrow behind the device)