Walter vl at 17:03, 2 February 2026

2026-02-02T17:03:39Z

← Older revision		Revision as of 17:03, 2 February 2026
Line 2:		Line 2:

	From Stable 2023.1 the Enphase integration has been updated to support Inverters (IQ7/8) and Storage (battery) on firmware 5 and 7.		From Stable 2023.1 the Enphase integration has been updated to support Inverters (IQ7/8) and Storage (battery) on firmware 5 and 7.

			From Beta 2025.2 the Enphase integration has been updated to support Inverters (IQ7/8) and Storage (battery) on firmware 8.

	Firmware 7 supports Authorization tokens, these are also supported.		Firmware 7 supports Authorization tokens, these are also supported.

Walter vl at 06:36, 21 August 2023

2023-08-21T06:36:27Z

New page

Domoticz supports the Enphase inverters. For each solar panel a measuring device can be created.

From Stable 2023.1 the Enphase integration has been updated to support Inverters (IQ7/8) and Storage (battery) on firmware 5 and 7.

Firmware 7 supports Authorization tokens, these are also supported.

===Create Hardware===

*Type: Select <code>Enphase Envoy with LAN (HTTP) interface</code>
*Enabled/Disabled: you can disable the hardware gateway. The created devices stay active (but greyed out) but will not be updated.
*Name: Enter a meaningful name for the Enphase Gateway
*Select Log Levels:
**'''Info''': Shows info logging about the hardware and its devices in the log file or log page. This will normally generate the most log lines
**'''Status''': Shows Status logging in the log file or log page.
**'''Error''': Shows Error logging in the log file or log page.
*Data Timeout: Enable Data Timeout if needed (1 minute to 24 hours). Domoticz will restart the Hardware thread/plugin if after the set timeout still no data is received by the gateway.
*Enter Enphase LAN IP address and port (default 80)
*Enter Username and password of Enphase online (not the installer account). If Token is requested leave empty an store the Token in Domoticz (see Token section)
*Set polling interval ( (5/10/20/30/60/120 seconds)
*Poll Inverters: Enable individual Inverters if needed. This will create a kWh device fore every individual inverter for monitoring.
*Site ID: Fill the Site ID (top left in enlighten site) to be able to switch on/off power generation. A separate on/off switch will be created.

Click on ADD to add the gateway to Domoticz. .

[[File:Enphase Hardware new.png]]

<br />

====Inverter Devices====
After adding the Domoticz Hardware Gateway a General kWh Device type production is created that monitors the complete installation of all inverters.

If Poll Inverters is enabled also a similar kWh device is created for each individual inverter.

Please check the device list (menu Setup - Devices) for new created Enphase devices and activate the if needed.

'''Note:''' Domoticz is only monitoring the inverter from 1 our before Sunrise to 1 hour after Sunset. If you enable/start the device outside this timeframe (in the dark) not all devices will be created immediately but only after the inverters become active.

'''Note:''' In a previous version of this integration a P1 Smart meter was created. This device is deprecated from 2023.1 Enphase integration and will not be updated anymore if present.

[[File:Enphase Kwh device.png]]

<br />

====Storage (battery devices)====
If the installation consists a storage facility the additional devices are created for monitoring the battery

*percentage device showing the battery level
*a Usage, Electric device that ways how much Watt device drawn or charged (negative value) from the battery
*a text device showing the mode (charging/discharging/idle)

[[File:Enphase battery storage.png]]

===Authentication Token===

'''Note''': Only when asked for.

When you are using Firmware 7 and you go directly to your Enphase Envoy's IP address you can be asked to create a token (points you to the website <nowiki>https://entrez.enphaseenergy.com/</nowiki> to do so)

Then copy this token and past it into the Enphase Envoy Autthentication page (see screenshot below) and submit to login the website.

This token is valid for at least a year when you do so.

Once you have done this, then you can use it in Domoticz.

When Domoticz logs in with the user/password it will read and store the token internally in a UserVariable starting with 'EnphaseToken_'

You can also use the contents of this uservariable to login to your system (instead of creating a new token)

[[File:Enphase Token.png]]
<br />

Enphase - Revision history

Walter vl at 17:03, 2 February 2026

Walter vl at 06:36, 21 August 2023